For commercial painters

Somebody told you to use ProCoustic. Here is what it is.

Most painters arrive here for one of two reasons. A specification on a job you are bidding called for ProCoustic, or a coatings rep told you to come and get it. Either way you are being asked to apply a product you may not have used, on a surface that does not behave like a wall.

  • Buy direct
  • One-year product warranty
  • Technical support included
  • Application guide
  • Standard white or custom tint
The part that catches people out

You would paint a wall. Why is a ceiling different?

An acoustical ceiling tile is a porous, perforated board built to absorb sound. The holes are the product. Fill them and the tile stops doing the job it was specified for, the room gets louder, and the surface burning rating no longer describes what is up there.

A general purpose coating bridges the gap between the tile and the grid as it dries. Once that happens the tile cannot be lifted out, which matters the first time anyone needs to reach a cable, a sprinkler head or a damper above the ceiling.

ProCoustic is non-bridging. It coats the tile, the grid, the air diffusers and the speaker plates in place, leaves the perforations open, and leaves the tile free to lift out afterward.

The perforations stay open

Noise reduction coefficient measured at 0.55 before and 0.60 after, a nine percent improvement, tested to ASTM C423 by NGC Testing Services in standard white.

The tile still lifts

No bridging at the tile and grid joint, so access above the ceiling is unchanged after coating.

Class A, retained

Flame spread falls from 25 to 0 and smoke developed from 10 to 5, tested to ASTM E84.

Why come to ProCoat rather than a counter

Three things you get by ordering direct

The right product, confirmed

Tell us the tile type and what is on it. We confirm what to order and whether the ceiling needs cleaning before anything is sprayed, which is the difference between a finish that holds and one that comes back through.

The application guide

Coverage, equipment, tip sizes, wet film thickness, recoat windows and the preparation sequence. Written for a crew that has not used it before.

Technical support before you quote

A call before the number goes out is worth more than a call after the crew is on site. We would rather tell you a ceiling needs replacing than sell you material for one that does.

Two ways to work with us

Buy the material, or hand us the program

Buy the product and apply it yourself

One building, a school, a church, a single store. You order the material direct, you apply it with your own crew, and technical support comes with it. The material carries a one-year product warranty.

Multi-site programs are turnkey

When an owner has locations in several states and needs every one to look identical, ProCoat manages the project and installs it. That route is what carries the fifteen-year color retention warranty, because the warranty depends on ProCoat having done the work.

ProCoat does not operate an approved applicator list. Crews change, and a list implies a guarantee about work ProCoat did not carry out. Where continuity across sites matters, the turnkey route is the answer.

On the job

How it goes on

PreparationContaminants bleed back through a coating applied over them. Grease, nicotine, cooking vapor and soot are cleaned first, with the cleaner matched to the contaminant
ApplicationAirless spray, in place, no tile removal
CoverageUp to 1,500 square feet per five-gallon pail at a single coat
BaseWater-based, low odor, no solvent
Return to serviceTypically the same night, open the next morning
ColorStandard white or custom tint

Coverage depends on the surface. A different tile type gives a different figure, so tell us what you are coating and we will give you a closer estimate. Confirm every figure against the current technical data sheet before you quote.

Clean before you coat

The most common failure is not the coating. It is a contaminant that was left in place and came back through it.

Coat the whole plane

Tile, grid, diffusers and speaker plates together. New tile dropped into an old grid is the look everyone is trying to avoid, and the same applies to a coated tile in an uncoated grid.

It can be done again

The same tile can be recoated again and again, which is what keeps the ceiling out of landfills.

A ProCoat applicator spraying ProCoustic onto a store ceiling from the floor, aisles below sealed under plastic sheeting
Coated in place from the floor. The aisles stay where they are, under cover.
Documents

What to ask for before you quote

Bidding a job that specifies ProCoustic

Ask for the three-part specification and the data sheet. The specification is written to drop into a master specification, and it states what the coating has to do rather than only what it is.

Not sure the ceiling is a candidate

Send photographs. Some ceilings are not sound candidates for a coating and need replacing. We will tell you which.